Bunn coffee maker cdbcf15 manual

The Bunn-O-Matic Corporation is famous manufacturing quality commercial coffee machines and filters. Bunn began manufacturing coffee making equipment for commercial kitchens and restaurants in Today, the Bunn product line includes coffee makers and grinders, tea brewers, thermal carafes, and other coffee maker parts and accessories. Page 20 There should be six sepa- rate streams of water coming out of the sprayhead. Count the number of flashes between pauses and use this chart as a guide to investigating the fault.

Page Service Each warmer assembly is attached with three 4- 40 screws. Page Control Board - Cdbc 7. Connect the pin connector and the 4-pin con- nector from the main wiring harness. Connect the blue wire and black wire to the relay on the control board. Page 23 Test Procedures: The test procedures for the control board will vary depending upon the problems experienced by the brewer. Test Procedures: The test procedures for the switch panel and the control board will vary depending upon the problems experienced by the brewer.

Test Procedure: 1. Disconnect the brewer from the power source. Viewing the switch from the back remove the white wire from the upper terminal and the black wire from the center terminal. Test Procedures: 1. Disconnect the blue and black wires from the limit thermostat.

Disconnect the brewer from the power supply. With a voltmeter, check the voltage across the white or red wire from the terminal block and the black wire from the control board.

Install tank lid and secure in place with eight nuts. Connect the two white wires of the tank warmer blanket. Connect the limit thermostat to the front of the tank assembly. The notices on this dispenser should be kept in good condition. Replace unreadable or damaged labels. Remove drip tray and cover from the parts box. Assemble the cover to the drip tray, then slide under the front door of the machine, engaging the rear of the drip tray into the opening in the lower front of the machine..

Remove the espresso brew group from the parts box. Slide tube onto elbow fitting on upper left side of espresso group head as shown in Figure 1. Place groove on lower front of group head over mounting bar on espresso drive as shown in Figure 2. Rotate the top of group head toward rear of machine until it snaps into place as shown in Figure 3. Slide red lock to the right until it snaps into place as shown in Figure 4. Install group head tube into quick connect fitting on bottom of espresso drive, insuring that the tube is fully inserted as shown in Figure 5.

Remove the bean hopper from the parts box. Align the bean hopper so that the collar on the bottom of the bean hopper will engage the opening in the grinder as shown in Figure 6. When the hopper is in place on the grinder, pull the hopper gate all the way forward to allow beans into the grinder, then lock hopper in place as shown in Figure 7.

Brew chamber has a capacity rating of 5 gm minimum up to 15 gm maximum of espresso grind coffee. Brewer has a peak capacity of 60 single small espresso shots per hour.

An electrician must provide electrical service as specified. Using a voltmeter, check the voltage and color coding of each conductor at the electrical source. Connect the dispenser to the power source. If plumbing is to be hooked up later be sure the dispenser is disconnected from the power source.

Note: This electrical service consists of 2 current carrying conductors L1 and Neutral and a separate conductor for chassis ground. This dispenser must be connected to a cold water system with operating pressure between -. A shut-off valve should be installed in the line before the dispenser. Install a regulator in the line when pressure is greater than. NOTE - Bunn-O-Matic recommends 6mm copper tubing for installations of less than 25 feet and 8mm for more than 25 feet from the water supply line.

At least 18 inches of an FDA approved flexible beverage tubing, such as reinforced braided polyethylene or silicone, before the dispenser will facilitate movement to clean the counter top. Bunn-O-Matic does not recommend the use of a saddle valve to install the dispenser. The size and shape of the hole made in the supply line by this type of device may restrict water flow. For models installed outside the U. NOTE - If a backflow preventer is required by code, a shock arrestor should be installed between backflow preventer and dispenser.

If you want a simplified guide on using this line of coffee machines, keep reading to learn more! Bunn coffee makers are automatic drip machines that use the pour-over method to brew coffee. They come in a variety of models, but the main difference between them is the brewing capacity.

These coffee makers are pretty easy to use, and they can brew a cup of coffee in just a few minutes! However, most people ask how do Bunn coffee makers work? This is because they have a unique brewing mechanism and pour-over drip coffee makers work differently from automatic drip ones. These coffee makers have a big tank in the back and a brewer funnel in the front.

The front side of most Bunn machines is a carafe warmer that keeps your coffee warm after brewing. Bunn coffee makers follow a pretty simple process. Once you pour filtered water into the brewer and close the lid, the brewer sends the water to the bottom of the tank via a special pipe.

Since the water already inside the water tank is hot, the cold water will push it upwards. This coffee machine is extremely simple to use and you can use it in any kitchen or office space with a power source. If you just unboxed a brand-new Bunn coffee maker, you need to set it up before brewing your cup of joe.

Once your coffee maker is all set up and ready, you can move onto making a steaming cup of coffee. The most common reason is usually a faulty heating element or a thermostat not working properly. However, your Bunn coffee maker can also experience issues with the control board, thermal fuses, and even an ill-functioning water heater switch.

The best thing to do with a Bunn coffee maker that refuses to heat up properly is to contact customer service. They will be able to tell you what to do next and how you may remedy the matter. In most cases, you will need to repair or replace the part of the coffee maker that is malfunctioning. This will prevent moisture and fungi from flourishing in the moist environment, and ensure your coffee always tastes crisp and fresh.

It generally takes a Bunn coffee maker about 15 minutes to heat the water in it.